Isolators
Vibration Reducing Isolators
Independent research documents vibration transmitted through percussive tools and chisels cause a variety of long term health and safety issues. Our isolators are intended for use when an operator uses a two-hand grasp on the tool. Isolators are installed over the barrel or chisel and utilize our polyurethane technology to reduce harmful vibration to the operators forward hand, much like we do with our low vibration handles.
Isolators for use with Riveter Barrels
HTRB-C79X Isolator on HTP7X
| Model# | Tool Type | I/D | O/D | O.A.L. |
| HTRB 5X | 5X Series | 1-1/2" | 2" | 2-1/4" |
| HTRB 7X | 7X Series | 1-1/2" | 2" | 3-4/5" |
| HTRB 9X | 9X Series | 1-1/2" | 2" | 3-4/5" |
| HTRB 2X10 | CP 2X | 1-1/5" | 1-1/2" | 1-1/2" |
| AVC 10 | 1-1/5" | 1-1/2" | 1-1/2" | |
| HTRB 3x12 | CP 3X | 1-1/5" | 1-1/2" | 2" |
| AVC 12 | 1-1/5" | 1-1/2" | 2" | |
| HTRB 4x13 | CP 4X | 1-1/5" | 1-1/2" | 3" |
| AVC 13 | 1-1/5" | 1-1/2" | 3" | |
| HTRB C 5X | 5X Series | 1-1/2" | 2" Hand 4" Collar |
2" |
| HTRB-C-B17 | B-17C, B-17E | 1-1/2" | 4" Collar | 4" |
| HTRB C 79X | 7 & 9 Series | 1-1/2" | 2" Hand 4" Collar |
4-3/5" |
| HT SBO2-C | B-17C, B-17CR, B-17E, P-51C, P-51CR, P-51E | 1-5/9" | 2" | 3-1/4" |
| HT SBO2-D | B-17D, B17DR, P-51D, P51DR | 1-5/9" | 2" | 1-1/4" |
<
Isolators for use with Chipping Hammers
| Model# | Tool Type | I/D | O/D | O.A.L. |
| HT9500 | Chipping Hammer Barrel Incl. Protective Collar |
2-1/4" | 2-3/4" Hand 4-1/2" Collar |
4" |
| HT9501 | Chipping Hammer Barrel | 2-1/4" | 2-3/4" | 3-1/4" |
Isolators for use with Scaler Barrels
HTSBO2 Isolator on HTIL 182
| Model# | Tool Type | I/D | O/D | O.A.L. |
| HT SBO1 | 356, BR, B1, 9356 | 1-13/20" | 2-3/20" | 5-1/4" |
| HT SBO2 | 456, 182 | 1-5/9" | 2" | 3-1/2" |
Isolators for use with Push-To-Start Throttles
HT-PTSI Isolator
| Model# | Tool Type | I/D | O/D | O.A.L. |
| HT PTSI | All Push-To-Start-Scalers | 9/10" | 1-3/8" | 13/20" |
Isolators for use with Chisels and Chipping Hammer Chisels
Chisel Isolators
| Model# | Tool Type | I/D | O/D | O.A.L. |
| HT 8000 CH | Hex, Round Shank | 9/10" | 1-1/2" | 4" |
| HT 8000 1 | 1/2" Square | 1/2" Square | 1" | 4" |
| HT 8000 138 | 1/2" Square | 1/2" Square | 1-3/8" | 4" |
| HT 8000 1R .498"-.401" Round |
5/8" Round | 5/8" Round | 1" | 4" |
| HT 8000 138R .498"-.401" Round |
5/8" Round | 5/8" Round | 1-3/8" | 5" |